Pulsed MIG Welder Aluminum Welding Machine 200Amps 4 in 1 Gas Gasless MMA REBOOT

  
We are the reboot practitioner for green environmental protection. Which welding DIY are you interested in? Take part in Reboot to become an imaginary welder! Focused on providing the best products and services to customers with a focus on the welding industry, since its development in 2010. The performance has increased and the market has been expanding. We have functional welding and plasma cutting machines, there is always one that suits you and always one that is tailor-made for you. All-in-one welding and cutting machine. Welding gun and consumable parts. Cutting gun and wearing parts.

Although we are young, we have spread out over many countries and regions and more and more welders have got to know our brand. We were born from a factory and have a solid foundation for quality assurance of the machine technology.

Which eliminates the price difference between the middlemen and keeps the price close to the people. The finished product is quick.

RBM-2000 4 IN 1 WELDING MACHINE! MMA / MIG GAS/ MIG GASLESS / Pulsed MIG. Voltage [V, Hz]: 220, 50/60.

MIG / MAG: 30 - 200. Efficiency [85%] (at an ambient temperature of 40 ° C). MMA: 60% - 150 A, 100% - 112 A. MIG / MAG: 60% - 200, 100% - 155 A. Power consumption [kVA]: 7.7.

Wire feed unit: inside, 2-roll. Welding wire diameter [mm]: 0.8 - 1.2. Size [mm]: 18.89x14.76x14.17 inch.

SPOT WELDING / GAS LAG TIME / 2T 4T. All parameters adjusted by steps. Will be automatically saved after the start of welding, and still. Remain unchanged even if the machine is shut down in the middle.

The welding rod specification supported by Reboot RBM2000P is below 4.0(5/32in), usually. 2.5(3/32in) and 3.2(1/8in). And stainless steel generally uses ER308.

But not suitable for special welding rods, such as 7010, 7011. It supports welding of 1-8mm(1/64-5/64in) carbon steel and 1-5mm(1/64-7/32in) stainless steel. Aluminum can not be welded. Please use carbon steel electrode. For stainless steel, please use stainless steel electrode.

Connect the ground clamp to clean bare metal. No rust, paint or other coatings, and ensure good electrical conductivity. Reboot RBM2000P provides two welding modes: gas shielded welding and self-shielded welding with fluxed wire. If you are working at home or in a studio, in order to ensure a better welding effect, it is recommended that you use the gas welding mode. If you need to go out to work, carry gas cylinders and other inconvenient situations, you can use the Self-protected welding method.

Just need to use 0.030'' and 0.040 Flux cored wire. You need to use 0.030'' and 0.040 solid wire. To replace the welding wire.

The welding wire should be extended outside the European central socket, and then install the welding torch. The wire guide tube and contact tip of the welding torch need to match the welding wire.

Long press the A knob, This is fast wire feeding, Let the welding wire be quickly delivered to the gun head. Please make sure that the welding torch is not bent, so that the welding wire will be blocked. Pulse gas shielded arc welding. You need to prepare aluminum welding wire.

Please strictly follow the picture instructions to connect, otherwise it will not be possible to solder. Aluminum welding wire supports 1.2mm(AL-Mg or AL-Si). The machine can install 5kg(11lb) and 1kg(2.2lb) wire reels. The machine comes with a 0.5kg(1.1lb) 5356AL-Mg welding wire and 1kg 2.2lb Flux-cored wire.

Support welding material is aluminum. The diameter of the welding wire, the groove of the wire feed wheel and the aperture of the contact tip must match. The pressure roller of the wire feeding structure should not be too tight or too loose, which will cause the wire feeding to be unstable. The installation of the wire feeding reel should not be too loose or too tight, which will cause the welding wire of the wire reel to spring off and the wire feeding is too slow.

Common gas shielded arc welding, carbon dioxide. Common gas shielded arc welding, mixed gas. Aluminum-magnesium pulse gas shielded arc welding, wire diameter of 1.2. Aluminium-silicon pulse gas shielded arc welding, wire diameter of 1.2.

For different welding methods, the inductance/arc. Enter the second level parameter setting interface.

It is used for manual covered-electrode welding. It is used for setting the gas preflow time. It is used for setting the low wire feed rate. It is used for setting the gas postpone time. It is used for adjusting the ball cutting effect at the.

It is used for restoring factory setting. It is used for setting 4T current downslope time. It is used for setting 4T arc extinguishing current. Follow EU ce certification, use more security. The export of each machine is controlled at various levels to ensure compliance with safety certification standards.

Item Processing Time: The processing time for a specific order depends on the product type and stock status. Processing time will be postponed during holidays or weekends. All our item offer 7 days return peroid, defective or non-defective. Return must include all original package and accesorries, item must in good condition. First-class talents and advanced equipment.

Mart Design with full digital control , Constant voltage and synergic adjustment control. Ully implement the ISO9001:2008 quality management system. Each Machine with 100% QC Test , Life Test and Welding Function Test, Drop test and Dust test! Over 10 years factory control system focus on the welding field. Please be patient when contacting us, all messages will be replied within 24 hours.

Please let us know immediately if a package is damaged upon arrival. The item "Pulsed MIG Welder Aluminum Welding Machine 200Amps 4 in 1 Gas Gasless MMA REBOOT" is in sale since Wednesday, September 1, 2021. This item is in the category "Business & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\MIG Welders".

The seller is "reboot-eu" and is located in Hebron, Kentucky. This item can be shipped to United States.

• Brand: REBOOT
• MPN: Does Not Apply
• Welding Process: Pulsed MIG
• Item Type: MIG Welder
• Voltage: 220 V
• Welded Material: Aluminum
• Feed: Automatic Feed
• Features: Gas / Gasless